Home / Services / Fire & Smoke Dampers

Life-Safety Dampers, Inspected and Installed

Fire and smoke damper inspection, installation and repair for commercial buildings across Helena and Central Montana, with written reports for your fire marshal and insurance carrier.
Fire & Smoke Dampers

Two Dampers, One Job: Contain the Spread

Dampers sit inside your ductwork where it passes through rated walls and floors. When a fire starts, they close off the path heat and smoke would use to travel through the building.
Heat Triggered

Fire Dampers

Installed where ducts cross fire-rated barriers. A fusible link melts at a set temperature and spring-loaded blades snap shut.
Smoke Triggered

Smoke Dampers

Tied into your fire alarm system. On an alarm signal, an electric actuator drives the blades closed to stop smoke migration.
What We Do

Inspection, Installation and Repair

Complete damper service from one local crew, from the first inspection to the final report.
01

Inspection

We open access panels, cycle every blade, check links and actuators, and tag each damper with a written pass or fail result.
02

Installation

New dampers are installed to your mechanical drawings and fire protection plans, anchored in rated sleeves and tested before occupancy.
03

Repair

Bent blades, corroded frames, failed actuators and missing links. Critical failures get fixed right away and minor issues get scheduled.
Certified Technicians

Credentials You Can Hand to the Fire Marshal

Our damper technicians hold International Certification Board credentials. Every report lists the technician’s credentials, each damper’s test result and any deficiencies found.
Work is performed to NFPA 80 for fire dampers and NFPA 105 for smoke dampers.
Fire, Smoke, and Fire Smoke Dampers.

Life-safety dampers, inspected and documented

Installation, inspection and repair for commercial buildings that need to stay NFPA compliant, with a written report for every damper.

Fire dampers

Installed where ducts pass through fire-rated walls, floors and ceilings to stop flames traveling through ductwork.

Smoke dampers

Wired to your fire alarm system to keep smoke out of egress corridors, stairwells and protected areas.
01

Inspection

We open access panels, clear obstructions, cycle every blade and check fusible links and actuators. Each damper is tagged and dated, and you get a written pass/fail report.

02

Installation

We work from your mechanical drawings and fire protection plans, anchor dampers in rated sleeves, seal connections, wire smoke dampers to the alarm panel and test before occupancy.

03

Repair

Bent blades, corroded frames, failed actuators and missing links. Critical failures are fixed right away; minor issues are scheduled into planned maintenance.

ICB-certified damper technicians

Our technicians hold International Certification Board credentials for inspecting, testing and documenting fire and smoke dampers to NFPA standards. Reports list technician credentials, test results and deficiencies, which helps you satisfy fire marshals and insurers.

NFPA 80 & 105

Inspection schedule

We line inspections up with your facility’s compliance calendar.
1
yr
Initial inspection after installation
4
yrs
Routine inspections for most buildings
6
yrs
Routine inspections for hospitals
Confirm intervals with your local authority having jurisdiction.
FAQ

Damper Questions from Building Managers

How long does an inspection take?

For a mid-sized facility, expect roughly 4 to 8 hours depending on how many dampers you have and how easy they are to access.

What are the most common failures?

Debris binding the blades, fusible links that have been painted over, actuators that have lost power, and corrosion on frames and sleeves.

Does Montana weather affect dampers?

Yes. Cold winters can cause condensation inside ductwork, which corrodes sleeves and frames over time and keeps blades from closing.

Will I get documentation?

Every inspection comes with a written report listing each damper’s location, test result, deficiencies and technician credentials.

Can you fix problems found during inspection?

Yes. Critical failures are repaired right away when possible, and minor issues are scheduled so your building stays compliant.
Trusted HVAC and custom fabrication in Helena, MT since 1985.

Contact Info

Office Location

Copyright 2026 Merit Mechanical Services, all rights reserved | Website Designed & Manged by Limitless Designs LLC

Scroll to Top